How Do I Make My Generator Start Automatically From My Solar System?

Most solar inverters have a generator start relay, also called a "2-wire start" or "dry contact." Connect it to an auto-start controller on your generator, and your solar system starts the generator when the batteries run low and shuts it down when they're charged. For the Predator 3500 and 9500, WEN 3800/4000/4500 inverter and Generac iQ3500, the GUS 2-Wire Auto-Start Kit plugs in with no cutting or splicing and works with Victron, EG4, Sol-Ark and most other inverters.

What is a 2-wire start, and does my inverter have one?

A 2-wire start is a simple switch inside your inverter or charge controller. When the batteries drop to a level you set, the switch closes. That's the signal to start the generator. When the batteries are charged, the switch opens again.

Victron, EG4, Sol-Ark and many others have one. To check yours, look in the manual for "generator start," "gen start" or "dry contact." Not sure? Text me your inverter's make and model and I'll check.

How auto-start works

Your solar system decides when the generator runs. The controller does the rest:

  1. Your batteries hit the low point you set, and the inverter closes its generator start contact.
  2. The controller sets the choke and cranks the generator. If it doesn't catch, it tries again.
  3. The generator runs and charges your batteries.
  4. When the batteries are charged, the inverter opens the contact.
  5. The controller runs a short cooldown, then shuts the generator off.

Minimum and maximum run times keep it from starting and stopping over and over, or running forever. Crank time and choke are adjustable for hot weather or freezing mornings.

Which kit do I need?

If you only want your solar system to run the generator, get the 2-Wire Auto-Start Kit. If you also want to start it from your phone or a key fob, or on a schedule, get the WiFi Full Kit.

2-Wire Auto-Start Kit WiFi Full Kit
Price: Predator 3500, WEN, Generac iQ3500 $249 $299
Price: Predator 9500 $259 $309
Solar auto-start (2-wire / dry contact) Yes Yes
Smart cold starts, choke and retries Yes Yes
Start when the generator battery is low, weekly exercise run, quiet hours Yes Yes
Travel / storage mode Yes Yes
Activity log, hour meter, oil-change reminders Yes Yes
Phone app Stop and settings Start, stop and settings
Key fob remotes No 2 included (Start, Stop, Eco)
Scheduled runs No Yes
Eco on/off from phone or fob No Yes
Home Assistant and Victron Cerbo GX over WiFi Yes Yes

Start with the 2-Wire kit and want more later? You can upgrade it to the full kit any time. No hardware change.

It works with no internet

The controller makes its own WiFi, and your phone connects straight to it, a lot like Bluetooth. There's no app to download, no account and no cloud. It works out in the woods with no cell signal.

Once it's set up, it runs on its own. Your solar system can start and stop the generator while you're away. You only need to be within WiFi range to check on it or change settings. At home, you can connect it to your home WiFi and open the app from any phone on that network. Firmware updates install by themselves when it's on your home WiFi.

Running a Victron Cerbo GX or Home Assistant? The controller can follow the Cerbo's generator relay over WiFi, with no 2-wire cable, and show up in Home Assistant. See the Home Assistant & Victron Cerbo setup guide.

Which generators does it fit?

  • Predator 3500, wheel brake on the right (as you face the control panel)
  • Predator 3500, wheel brake on the left
  • Predator 9500
  • WEN 3800 / 4000 / 4500 inverter (not dual fuel): the same models as my WEN remote start kit. Not sure your WEN matches? Send me a photo before you order.
  • Generac iQ3500: same plug-in connections as the Predator 3500 with the brake on the right
  • Predator 9000 Open Frame: coming soon. The harness is being finished now.

Not sure which 3500 you have? See how to check your wheel brake side, or order both harnesses for $10 more.

The controller is built to work with most electric-start generators. Each model just needs its own plug-in harness and choke setup. Tell me your make and model, and the ones people ask for most get built next.

Like all my kits, it plugs into your generator's own connectors. No cutting, splicing or soldering. You can still run the generator by hand, and it goes back to stock for warranty work.

Common questions

Will it work with my Victron (or EG4, or Sol-Ark)?

If your inverter or charge controller has a generator start relay, it should. Victron, EG4 and Sol-Ark all have one. If you're not sure about yours, text me the model and I'll check.

Can the generator start when nobody is home?

Yes. That's the point. Once it's set up, your solar system starts and stops the generator on its own. No phone or internet needed.

What keeps it from starting and stopping over and over?

You set a minimum and maximum run time. The generator won't shut off before the minimum or run past the maximum. Every automatic stop also gets a cooldown run first.

What if it doesn't start on the first try?

The controller works the choke for you and tries again. You can adjust crank time and choke for hot weather or cold starts.

How do I stop it from starting while I'm towing or storing it?

Flip on travel/storage mode. It blocks every automatic start with one switch.

Can I upgrade from the 2-Wire kit to the WiFi Full Kit later?

Yes, any time. No hardware change.

I already have one of your remote start kits. Can I upgrade it?

No. The V1, V2 and V3 remote start kits are RF-only, so they can't be upgraded to WiFi or solar auto-start. You'd need the 2-Wire Auto-Start Kit or the WiFi Full Kit. Only the 2-Wire kit can be upgraded to the WiFi Full Kit later.

Do I already need a remote start kit for this?

No. Either kit does the whole job on its own. The WiFi Full Kit also includes everything my remote start kits do.

Can I still start my generator by hand?

Yes. Manual start and stop work the same as before, and the kit comes off if you ever need warranty work.

Pre-order and shipping

Both kits are on pre-order now. Use code WIFI20 for 20% off. The pre-sale ends December 18, and kits ship by January 22. Orders ship in the order they came in. Change your mind before yours ships? Full refund.

Who's answering

I'm Kenny Wharton, Marine veteran and owner of Generator Upgrade Supply. I designed this controller because I wanted it on my own generators. Every kit is hand-assembled here in Peoria, Arizona, and I answer customer questions myself.

Not sure which kit fits your setup? Text me your inverter and generator model before you order. I'll give you a straight answer.

In your corner,
Kenny