How Do I Add Remote Start to My Predator 3500?

You add remote start to a Predator 3500 with a plug-and-play kit that connects to the generator's existing wiring. There's no cutting, splicing, drilling or soldering. Most people finish in about an hour with basic hand tools, and the remote works from over 200 feet away.

What you need

Plan on about an hour. You'll need:

  • Phillips and flat-head screwdrivers
  • #7, #8 and #10 sockets, or an adjustable wrench (#10 is only needed on the right-brake style)
  • Needle-nose pliers (left-brake style, to unlock the start connector)
  • A Torx security bit set, only if your generator has a CO sensor. Harbor Freight sells one for about $6.
  • Optional: a 1/4" drill bit, only if you want to keep the reset button and mount the kill switch somewhere else

You also need a charged battery in the generator. The kit runs off it.

Step 1: Check which side your wheel brake is on

Harbor Freight has sold two styles of the Predator 3500 at the same time since May 2021. They take different wiring harnesses, so check this before you order.

Stand facing the control panel. Look at where the battery compartment and the wheel brake are. If they're on your right, you need the right-side harness. If they're on your left, you need the left-side harness.

Don't go by the panel labels. They look the same on both styles. If you're not sure, you can order both harnesses for $10 more.

Right-side brake and left-side brakePredator 3500 with the wheel brake on the right sidePredator 3500 with the wheel brake on the left side

How the install works

The kit plugs into the wiring that's already on your generator. Nothing gets cut or spliced, so you can still start it by hand. You can also remove the kit and put the generator back to stock if you ever need warranty work.

Here's the install at a glance:

  1. Disconnect the battery.
  2. Remove the front control panel (six Phillips screws plus the one in the knob).
  3. Mount the module behind the front panel and plug it into the start and stop connectors. Every connection is plug-in: male to female.
  4. Install the kill switch. It replaces the reset button next to the DC 12V outlet, or goes in a 1/4" hole anywhere on the panel.
  5. Open the side panels. On the right-brake style, you'll take the right wheel off to free the panel.
  6. Mount the choke actuator and run its cable alongside the stock choke cable. Pull it tight so there's no slack.
  7. Reconnect the battery, turn the knob to RUN and test with the remote.

The printed instructions in the box have photos for every step.

Watch the video that matches your generator before you start:

Have a Predator 9500? See the Predator 9500 remote start guide.

If you have a question before you start, text or email me. It's easier to answer before the panels come off.

What the V3 kit does

V3 runs on a circuit board I had custom-made for generators. It does everything the earlier kits did. Here's what it includes:

  • Rolling-code remote. Every button press sends a new code, so it can't be copied.
  • Starter protection. Start cuts out after 5 seconds if you hold the button. Pressing Stop cancels Start right away.
  • Adjustable timing. Each button can be set to momentary or timed from 0.5 to 15 seconds.
  • Electrical protection. Reverse-polarity protection, a resettable fuse and surge protection on the 12V input.

V3 kits start shipping November 18. Orders ship in the order they came in.

Common questions

Will this kit fit my generator?

The Predator 3500 kit also fits the Powerhorse LC3500i, Echo Bear Cat IG3500, BE i3500L, Loncin LC3500i, Atlas Copco P3500i and JET JIN 3500E. The Generac iQ3500 needs a quick change to the actuator bracket. I also make kits for the Predator 9500 and the older style WEN 3800/4000/4500.

Can I add remote start to a pull-start generator?

Not with this kit. Remote start needs an onboard battery and electric starter to work with. Pull-start-only models don't have them.

Do you make a kit for the Predator 4200 or 5000?

Not yet.

How far does the remote reach?

Over 200 feet.

I press Start and hear a clunk, but it won't start. What's wrong?

That's almost always the generator's battery. It's either not fully charged or getting old. Charge it or replace it and try again.

How do I start and stop it with the remote?

Turn the generator knob to RUN. Press and release A for about a second to start. Press B to stop (on the left-brake style, press and hold B). C and D aren't used.

My generator battery keeps going dead. Why?

Check two things. First, the antenna and its base can't touch the frame. If it grounds out, it keeps the module on and drains the battery. Second, when you're not using the generator, keep the knob on STOP and the kill switch OFF.

What's the kill switch for?

It shuts off power to the module, so the remote can't start the generator and the module isn't drawing from the battery. Switch it on when you want to use the remote.

I switched to the other style of 3500. Do I need a whole new kit?

No. Text me. I can swap the wire harness at the pigtail, and you won't have to reinstall the module or the choke actuator.

Can I still start my generator by hand?

Yes. The kit doesn't take anything away. Manual start and stop work the same as before.

Will this void my warranty?

The kit unplugs and the generator goes back to stock, so you can remove it before any warranty work.

Who's answering

I'm Kenny Wharton, a Marine veteran and the owner of Generator Upgrade Supply. I build and hand-assemble these kits in Peoria, Arizona, and I answer the questions myself.

If you're not sure the kit fits your generator, text me a photo of your control panel before you order. I'll tell you straight.

Shop the Predator 3500 Remote Start Kit

In your corner,
Kenny